Creality Space PI PlusBest overall- Max temperature
- 70°C
- Capacity
- Two spools
- Timer
- 0–48 hours
Most recommended by reviewers
Check price at AmazonWe earn a commission when you buy through our links, at no extra cost to you. How this works.
If your prints are stringing, clogging or coming out brittle, damp filament is often the cause. A filament dryer heats your spools to drive moisture out and keeps them dry while you print.
Our top pick is the Creality Space Pi Filament Dryer Plus. It has dual heaters that circulate warm air around two spools, reaches 70°C, and suits anyone running two materials or two printers. The other picks cover single spools, budget use and four-spool setups.
1 Creality Space PI Plus | 2 SUNLU Filament Dryer S2 | 3 EIBOS Cyclopes Filament Dryer | 4 Sovol SH01 Filament Dryer | 5 Creality Space Pi X4 | |
|---|---|---|---|---|---|
| Best for | Best overall | Best single-spool | Best for multi-spool storage | Best budget | Best for high-volume |
| Max temperature | 70°C | 70°C | 70°C | 50°C | 85°C |
| Capacity | Two spools | Single spool (210×85 mm) | Two 1 kg or four 0.5 kg spools | Two 1 kg spools | Four 1 kg or two 2 kg spools |
| Check price at Amazon | Check price at Amazon | Check price at Amazon | Check price at Amazon | Check price at Amazon |
Creality Space PI PlusBest overallMost recommended by reviewers
Check price at Amazon
SUNLU Filament Dryer S2Best single-spool
EIBOS Cyclopes Filament DryerBest for multi-spool storage
Sovol SH01 Filament DryerBest budget
Creality Space Pi X4Best for high-volume




A dual-spool dryer with dual PTC heaters and a touchscreen, best for two-material or two-printer setups.
Most recommended by reviewers
Check price at AmazonPrices and availability on Amazon change often.
The Creality Space PI Filament Dryer Plus is our best overall pick for anyone who wants to dry two spools at once with plenty of control.
Two PTC heaters circulate warm air around both spools, and reviewers note that the touchscreen and its 12 material presets make setup simple. Its timer runs from 0 to 48 hours, the longest of the picks we compared, and the two filament outlets suit either a dual-material setup or a workflow that feeds two printers. Owner reports were not available for this pick.
The footprint is larger than the single-spool options, so make sure you have the shelf space. Reviewers also advise confirming the exact Plus model before ordering, since the Plus and V2 Plus variants differ.
If it's not for you, the SUNLU Filament Dryer S2 suits a single printer with a compact box, while the Sovol SH01 fits a tighter budget but tops out at 50°C.
Reviewers highlight dual PTC heaters that circulate warm air evenly around two spools, reaching 70°C. The touchscreen and material presets make setup simple, and the two filament outlets suit workflows running two materials or two printers.
It is larger than single-spool units, so it suits a dedicated spot near the printer rather than a shelf.





A compact single-spool dryer with 360° heating and a 4.6-inch touchscreen, for one printer and one material at a time.
Prices and availability on Amazon change often.
The S2 is a compact dryer for a printer that normally runs one material at a time. Its display reports temperature, time, humidity and filament type, and it reaches 70°C.
Reviewers note it is not built for two spools, so buy it for a single-printer setup.





A large dryer with a 100W PTC heater and built-in fan, holding two 1 kg spools or four 0.5 kg spools.
Prices and availability on Amazon change often.
Reviewers praise the active fan and PTC heater, which move air through the box. It holds two 1 kg spools or four 0.5 kg spools and can run up to 24 hours.
The size is the trade-off, so it suits multi-spool users with room for it.





A budget dryer for two standard spools with a 40–50°C range and a 6–12 hour timer.
Prices and availability on Amazon change often.
The SH01 is a sensible pick for a tight budget. It holds two standard spools, shows temperature and humidity, and seals well enough to store filament without power.
Check your filament maker's drying temperature first, since the 50°C limit won't reach what some materials need.





A four-spool dryer with dual 200W heaters reaching 85°C, for high-volume and engineering filaments.
Prices and availability on Amazon change often.
Reviewers note the dual 200W heaters reach 85°C, enough for engineering filaments such as PA, PAHT and PC. It holds four standard spools and can run one chamber to save energy.
It is the most expensive pick, so it suits high-volume users.
Pick a single-spool dryer for one printer and one material. Choose a dual or four-spool unit if you run several materials or printers at once.
If your filament is dry and stored well, a dryer may not be needed. Check the drying temperature your filament maker recommends before buying.
The Creality Space Pi Filament Dryer Plus is our top pick. Its dual heaters dry two spools evenly up to 70°C, and it suits two-material or two-printer setups.
Any of the single-spool picks works for a Bambu printer, such as the SUNLU S2 for a compact setup. Match the dryer to how many spools you print from.
Nylon and PA6-CF need higher temperatures. The Creality Space Pi X4 reaches 85°C, which suits engineering filaments like PA and PAHT.
Many filaments absorb moisture from the air, so a dryer helps prints come out cleanly. Over-drying is rarely a problem, but follow your filament maker's drying temperature and time.
Meet the reviewer

Commerce Writer & Editor
Luka Lucheski is a content writer and editor with more than five years of experience in commerce content and digital publishing. He specializes in product reviews, buying guides, and comparison content. Over the years, he has edited and reviewed hundreds of articles across a wide range of categories, from tech and software to ecommerce and everyday consumer products.
Why trust CheckedBest
Every dryer here is in stock on Amazon today, and each one was checked against its listing and against what experts and owners say about heat, capacity and ventilation. Picks are weighed on how well they dry filament and how they handle moisture, not on lab numbers.
Our expert team tests products when it is needed and researches online and in interviews. Every guide is fact-checked and edited by a real person.
The CheckedBest editorial team · Updated Nov 5, 2026
How we pickEditorial standardsAffiliate disclosureReport a mistake
We earn a commission when you buy through our links, at no extra cost to you. It never decides the winner.